AC repair
Furnace & heating
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateWhy Paradise Homeowners Choose Lennox HVAC
We provide independent Lennox HVAC service in Paradise, NV: repair, installation, and full system service for Lennox equipment of every vintage and every series. What makes our Lennox work different is that we’re not tied to the brand, so a diagnostic visit ends with what your system actually needs rather than what a dealer is scheduled to move that month. Lennox is one of nine manufacturers we’re certified to service, and it’s the one we see most often in the valley’s newer Signature builds and its older Merit and Elite installs. To book a visit, call (844) 820-2853. We answer 24/7, with fast dispatch from 7am to 7pm. One clear point up front: we are an independent Lennox service provider. We are not affiliated with, authorized by, or endorsed by Lennox.

Key Takeaways
- We service, repair, and install Lennox equipment across every residential series, as an independent shop.
- We’re certified across nine leading brands, so our advice isn’t steered by brand loyalty.
- Repair or replace, one visit covers both conversations – including heat exchanger findings.
- Our technicians have up to 9 years of experience.
Why Trust AC Repair Paradise for Your Lennox HVAC?
Technicians who work on Lennox systems regularly learn its habits. That means understanding what a pressure-switch fault means on a G-series furnace before pulling the board, why a short-cycling XC unit in July is so often a marginal dual-run capacitor rather than a refrigerant problem, and how the communicating low-voltage controls on Signature Collection systems report faults differently from a conventional 24-volt setup. That kind of pattern recognition is what shortens a diagnostic visit.
We use OEM Lennox parts for boards, ignitors, flame sensors, and heat exchangers whenever they’re available and the price makes sense for the repair. For capacitors, contactors, and fan motors, a quality aftermarket part that meets spec often does the job just as well for less, and we’ll say so plainly rather than pad the invoice.
Warranty-safe service matters too. How your system is serviced affects whether a manufacturer’s parts warranty stays intact, so we document what we find, use parts that fit correctly, and never modify a system in a way that would put warranty coverage at risk. That’s the standard for every Lennox call we take in Paradise. If you’d rather ask first, call (844) 820-2853 – estimates are free.
Styles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
Common Lennox HVAC Problems We Fix in Paradise
These are the Lennox failure patterns we see most often in Paradise homes. Matching your symptoms to a likely cause before the technician arrives makes for a much faster visit.
- Failed secondary heat exchanger in older G40, G50, and G60 furnaces, and early ML180s. The stainless secondary coil can corrode or block over time, which shows up as a pressure-switch fault, visible corrosion at the exchanger, or restricted flue flow. It’s the failure that most commonly drives a furnace replacement on a G-series unit. Not every pressure-switch trip means the exchanger is gone, so a proper inspection comes first.
- High head pressure and short cycling on XC13, XC14, and 13ACX air conditioners in summer. These units are common on Paradise homes where the condenser sits close to a stucco wall with restricted airflow. A dirty outdoor coil, a failing condenser fan motor, or a dual-run capacitor running below spec all show up the same way on a 110°F afternoon: the system starts, runs, and shuts off early, never reaching setpoint.
- Ignition lockout on ML180, ML193, and Elite furnaces. A worn hot-surface ignitor or a flame sensor coated with carbon will lock the furnace out after the off-season. Desert dust settles into the burner compartment during months of no use, and the flame sensor is the first thing to complain.
- Control board and low-voltage communication faults on Dave Lennox Signature Collection systems. On SL280V, SLP98V, and XC25 systems, a fault that looks like a failed board or inverter is sometimes a communication issue at the thermostat, a low-voltage wiring run, or a fault code the board is reporting correctly. These need meter and fault-code verification, not a parts swap.
- Brittle flex duct and baked air handlers in older Paradise tracts. In the 1960s and 1970s ranch tracts near the airport and east of the Strip, attic air handlers and flex duct have cooked in attic temps that top 150°F summer after summer. The result is duct that splits and leaks and an air handler that runs harder to move the same air. It’s a comfort and efficiency problem that shows up as weak cooling at the registers, not a failed component.
If you’re seeing any of these symptoms, call (844) 820-2853. Same-day service is often possible, and estimates are free.
Lennox Parts & Our Repair-vs-Replace Approach
Parts choice on a Lennox call is a judgment call, and we make it in the open. OEM Lennox parts for boards, ignitors, flame sensors, and heat exchangers are the default when they’re available and the price is sensible. For capacitors, contactors, and fan motors, a quality aftermarket part that meets the same spec is often the smarter spend. We’ll tell you which is which on the estimate, and the written estimate sets the final price.
Repair or replace comes down to age, condition, and how many major components are on the edge. On a unit roughly 12 to 15 years old with a failed heat exchanger or a failed compressor, an honest answer is usually that replacement makes more sense than sinking money into a second major repair. That’s especially true on a G-series furnace where the secondary exchanger has failed, or on an older system where the compressor is on its way out. If both options are open, we’ll price them out and let you decide.
The older tracts around the airport and east of the Strip add one more thing to check: condenser pads set on bare desert caliche shift over the years, and that movement can crack refrigerant lines slowly. Sometimes that’s a line-repair job, sometimes it’s a relocation; we’ll tell you which. Call (844) 820-2853 for a straight answer.
Our Lennox Service Process – Step by Step
A typical call on a Lennox system follows the same path every time, whether it’s a repair or a replacement conversation.
- 1
Diagnosis. We check the fault codes your Lennox board reports, verify capacitor microfarads against spec, and confirm pressures and subcooling before we call anything. On a Signature Collection system, that means meter verification of low-voltage and communication faults rather than assuming the board is bad. On a furnace pressure-switch fault, we inspect the secondary heat exchanger before touching the board.
- 2
Repair or install. For a repair, we replace the failed component with a part that meets spec – OEM where it matters, quality aftermarket where it makes sense. For an install, the system is load-calculated for your home and the outdoor unit is sited so the coil isn’t starved for airflow against a wall. That’s a real factor in Paradise, where stucco and small courtyards crowd most condenser pads.
- 3
Test. After any Lennox repair, we run the system through a full cycle – flame current verified at the sensor, subcooling and superheat confirmed, a full heating or cooling cycle completed – so nothing is declared fixed until the numbers back it up.
- 4
Warranty and documentation. Every visit ends with what was found, what was replaced, and any warranty paperwork you’d need. For a new install, that includes registration documents for the manufacturer’s parts warranty.
See the difference
Before
After
Before
After
Before
AfterLennox Products We Service & Install in Paradise
We service and install the full residential Lennox lineup, from the oldest G-series furnaces still running in Paradise’s mid-century tracts to the Dave Lennox Signature Collection systems going into new builds and condo towers.
On the heating side, that includes G40, G50, and G60 furnaces, the ML180 and ML193 Merit and Elite furnaces, and the SL280V and SLP98V Signature furnaces. On the cooling side, we cover the 13ACX and 14ACX Merit air conditioners, the ML14XC1 and ML16XC1 value-series units, the XC13 and XC21 Elite air conditioners, and the XC25 Signature. We service the air handlers, coils, and controls that go with each. If your Lennox nameplate matches any of those, we know the family and its failure patterns.

We Also Service These Brands
We’re certified across nine leading HVAC brands, and that’s not a footnote – it’s why our Lennox advice stays grounded. We work on Carrier and Trane systems alongside Lennox, plus Goodman, Rheem, York, Daikin, Bryant, and American Standard. That range means a recommendation is driven by your home and budget, not by which brand we happen to carry. Nine brands, one call, one honest assessment: call (844) 820-2853.
FAQs – Lennox HVAC Service in Paradise
No. We are an independent Lennox service provider. We’re not affiliated with, authorized by, or endorsed by Lennox. We’re certified to service Lennox equipment and eight other leading brands, and we don’t claim manufacturer authorization. What that means for you: our recommendations are based on your system’s condition and your budget, not on a dealer requirement. Call (844) 820-2853 with questions.
Yes. We use OEM Lennox parts for boards, ignitors, flame sensors, and heat exchangers whenever they’re available and the price makes sense, and quality aftermarket capacitors, contactors, and fan motors that meet the same spec when they don’t. Every part is chosen to fit your equipment correctly and preserve the manufacturer’s warranty coverage. Call (844) 820-2853 for a written estimate.
Most Lennox repairs are completed in a single visit, usually one to three hours depending on the component and how accessible the system is. Diagnostics on communicating Signature Collection systems can take longer because the fault has to be verified at the board and the thermostat. Installations are scheduled separately after a load calculation. Call (844) 820-2853 to book; same-day service is often possible.
We cover the full residential Lennox lineup: gas furnaces, air conditioners, air handlers, coils, and the controls that run them. That includes older G-series furnaces, Merit and Elite equipment, and Dave Lennox Signature Collection systems. We also service the auxiliary components – ignitors, flame sensors, capacitors, fan motors, heat exchangers, and boards – as part of any repair visit. Call (844) 820-2853 for a quote.
Correctly performed service does not void a Lennox warranty, and we take care to protect it. We use parts that meet spec, document what was replaced, and don’t modify your system in ways that would put coverage at risk. Improper service is what typically causes warranty problems, not the fact of service itself. For a written estimate and warranty-safe service, call (844) 820-2853 – estimates are free.
Typical estimated ranges for Lennox service in Paradise: AC repair $150 – $650, furnace repair $150 – $700, AC installation $3,500 – $7,500, and a tune-up $80 – $200. The written estimate sets the final price, since the number varies by the component, the system’s age, and how accessible the equipment is. Call (844) 820-2853 for an exact quote – estimates are free.
No. A pressure-switch fault means the furnace’s draft proving has failed, and that can come from a blocked flue, a failing inducer motor, a bad pressure switch itself, or – on G40, G50, G60, and early ML180 furnaces – a blocked or corroded secondary heat exchanger. The exchanger is the worst-case answer, so we inspect it before condemning anything else. Call (844) 820-2853 to book a diagnosis.
On a 110°F afternoon, head pressure climbs and electrical draw climbs with it, so a marginal component that runs fine at 95°F trips at 115°F. The usual culprits are a dual-run capacitor running below spec, a condenser fan motor that’s drawing high amps, or a coil packed with dust restricting airflow. It’s often a capacitor swap and a coil wash – but it needs verification with a meter, not a guess. Call (844) 820-2853.
Not always, and sometimes not at all. On SL280V, SLP98V, and XC25 systems, a communication fault can come from the thermostat, the low-voltage wiring, a failed inverter, or the board itself. The correct path is meter and fault-code verification at each point before replacing a board, because OEM boards are expensive and the wrong call is a costly mistake. Call (844) 820-2853 for a diagnostic visit.
A glowing ignitor with no flame almost always points to a gas supply problem or a flame sensor that has never been asked to prove anything because ignition never completed. The gas valve, the gas pressure, and the sensor itself all need checking in sequence. It’s not a “replace the ignitor” problem, because the ignitor is working. Call (844) 820-2853 and we’ll sort it out.
Roughly 12 to 15 years old with a failed heat exchanger or a second major repair behind it, replacement usually makes more sense than another repair. Below that age, a single component failure like an ignitor, flame sensor, or inducer is almost always worth fixing. Paradise’s long cooling season pushes furnaces through a lot of cycles per year, so age alone isn’t the whole story – condition is. Call (844) 820-2853 for a straight repair-vs-replace answer.
Book Your Lennox Service in Paradise, NV
If your Lennox system is short-cycling, locking out, or just not keeping up, we’ll diagnose it, price the fix, and tell you straight whether repair or replacement makes more sense. Call (844) 820-2853. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Estimates are free.
Written by the team at AC Repair Paradise.